Return Policy
Shipping Info
Warranty
Privacy Policy
Terms of Service
Cookie Policy
FAQ
Return Policy

1. Statutory Right of Withdrawal for Online Purchases

For eligible distance purchases, consumers have a statutory right to withdraw from the contract without giving a reason within 14 days. PUCKIPUPPY voluntarily extends the request period to 15 days after delivery for eligible non-quality-related returns under this policy. This voluntary extension does not reduce any longer mandatory period that may apply.

For a single order delivered in several lots or pieces, the statutory period is calculated in accordance with applicable law, including from receipt of the last lot or piece where required. To exercise the right, the consumer must send a clear statement of withdrawal before the deadline by email to support@puckipuppy.eu or by using any withdrawal function/form made available on our website.

After notifying us of withdrawal, the consumer must return the goods without undue delay and, for the statutory withdrawal right, no later than 14 days after communicating the withdrawal, unless we have offered to collect the goods or applicable law provides otherwise.

Direct return cost for e-bikes

E-bikes are bulky goods that normally cannot be returned by ordinary post. For a non-quality-related withdrawal, the consumer bears only the direct cost of returning the goods where we informed the consumer of that obligation before the contract was concluded. The estimated direct return transport cost is up to EUR 300 per e-bike, depending on route, carrier and collection requirements. We will not treat this amount as a cancellation penalty. If applicable law requires PUCKIPUPPY to bear the return cost, the consumer will not be charged.

Any outbound transport cost already borne by PUCKIPUPPY will not be charged to the consumer merely because the consumer exercises the statutory right of withdrawal, except to the extent expressly permitted by mandatory law.

2. Product Inspection, Use and Diminished Value

Consumers may handle and inspect goods only to the extent necessary to establish their nature, characteristics and functioning, comparable to what would reasonably be permitted in a physical shop. For an e-bike, mileage is only one factor and no fixed mileage threshold automatically removes the statutory right of withdrawal.

Where permitted by law, the consumer may be responsible for actual diminished value resulting from handling beyond what is necessary for such inspection. Any deduction will be based on the actual condition and impact on value, including avoidable damage, missing parts or excessive use, and will not be an automatic fixed restocking fee.

3. Return Procedure

· Send your order number, name, delivery country, product model/serial number (if available), and the requested solution to support@puckipuppy.eu.

· For quality or shipping-damage claims, provide reasonable photos/videos where available to help us diagnose the issue. Such evidence requirements will not be used to remove statutory rights where the defect can otherwise be established.

· Wait for the return address and carrier/packing instructions before sending a bulky e-bike, so the return can be identified and safely handled. This administrative step does not cancel a timely statutory withdrawal notice.

· Return all components and accessories supplied with the product and package the product safely. Original packaging is recommended but is not an absolute condition for exercising statutory rights.

4. Refunds After Withdrawal

Where the consumer validly withdraws, we will reimburse payments received from the consumer, including the cost of our least expensive standard delivery option where required by law, without undue delay and no later than 14 days after we are informed of the withdrawal. We may withhold reimbursement until we have received the goods back or the consumer provides evidence of having sent them back, whichever occurs first, where permitted by law.

Refunds will normally be made using the same payment method used for the original transaction, unless the consumer expressly agrees otherwise and does not incur fees as a result. Extra delivery charges resulting from the consumer choosing a more expensive delivery method than our standard option need not be refunded where permitted by law.

5.Model Withdrawal Notice

Consumers may use the following wording, but use of this exact form is not required: “I/We hereby give notice that I/We withdraw from the contract for the sale of the following goods: [product], ordered on [date] / received on [date], order number [number], name [name], address [address], date [date].” Send the notice to support@puckipuppy.eu or through the withdrawal function available on the website.

6. Defective, Damaged or Non-Conforming Goods

Statutory conformity rights are separate from the 15-day voluntary return policy. If goods are defective, damaged in transit, not as described, or otherwise non-conforming, consumers may be entitled to remedies under applicable law regardless of whether the voluntary return period has expired.

Where required by law, repair or replacement will be provided free of charge, including necessary shipping, parts and labour, within a reasonable time and without significant inconvenience. Depending on the circumstances and applicable law, a proportionate price reduction or termination/refund may be available where repair or replacement is impossible, disproportionate, refused, unsuccessful, not completed within a reasonable time, or where the lack of conformity is sufficiently serious.

7. Exchanges and Order Changes

Before dispatch, contact us as soon as possible if you wish to cancel, change the delivery address or change model. We will try to assist, but warehouse processing may make a change impossible. This operational process does not limit a statutory withdrawal right that applies after the contract is concluded.

A voluntary model exchange for a non-defective product may be handled as a return of the original product and a new purchase. Direct return/reshipment costs may apply where clearly disclosed and permitted by law. Defective or non-conforming goods are handled under statutory conformity rights, not as a paid voluntary exchange.

8. Contact and Claims

Customer Support: support@puckipuppy.eu
Website: www.puckipuppy.eu

When contacting us, please provide where applicable:

order number;

customer name and contact details;

delivery country/address;

product model and serial number;

description of the request or defect;

preferred solution;

and relevant photos/videos where reasonably available.

9. Policy Updates and Governing Mandatory Law

We may update this policy prospectively to reflect operational or legal changes. The version applicable to an order is the version made available to the consumer in connection with that order, without prejudice to later mandatory legal rights. Nothing in this policy deprives a consumer of the protection of mandatory law that cannot lawfully be excluded by contract.

10. Important Notice

By purchasing and using a Puckipuppy e-bike, the customer acknowledges that cycling involves risks and hazards, including but not limited to traffic conditions, weather conditions, obstacles, and the behavior of other road users. The customer is responsible for safe use, maintenance, and control of the product. Puckipuppy is not liable for loss, injury, or damage resulting from improper use, improper assembly, failure to follow safety instructions, or failure to use appropriate protective gear.

11. Privacy and Data Processing Notice

When you contact us, we process your personal data (name, contact details, order information, photos or videos you provide) solely tohandle your request, on the legal basis of performance of the contract or compliance with legal obligations. Data may be transferred tooand processed by service providers outside the European Economic: Area under appropriate safeguards (e.g. EU Standard ContractualClauses). Retention periods and your rights (access, rectification, eraasure, objection, complaint to a supervisory authority) are describedd inour Privacy Policy: https://eu.puckipuppy.com/pages/privacy-policy.

Purchase

How long will it take for me to receive the electric bike I purchased?

Typical delivery time is 2–10 business days unless another estimated delivery time is displayed at checkout or in the shipping confirmation.

Delivery may take longer during public holidays, high-volume order periods, new product launches, pre-orders, restocks, logistics disruptions, or severe weather. Where possible, the estimated shipping date will be shown on the product page or communicated to you by email. 

Where do we sell and ship?

PUCKIPUPPY EU currently delivers to Germany, France, the Netherlands, Italy, Poland and Spain, subject to product availability and carrier coverage.

Delivery availability, shipping charges and estimated delivery times shown at checkout form part of your order information. 

Are taxes included?

Applicable prices, shipping charges and taxes will be displayed in accordance with applicable law and the information shown at checkout.

For the countries currently supported by PUCKIPUPPY EU, please review the final order amount displayed at checkout before completing your purchase.

Nothing in our policies limits any mandatory consumer rights available under applicable EU or national law. 

Do electric bikes need to be assembled?

Electric bikes arrive partially assembled and require a few additional steps to complete the assembly. Please carefully watch the assembly tutorial or refer to the electric bike user manual for installation instructions. Assembly Tutorial.

How can I track my order?

You can click on "Track" to view your order status.

Can discounts be stacked?

Only one coupon can be used per order, and we do not support coupon stacking. The final interpretation right belongs to PUCKIPUPPY.

Cycling

What is the most suitable electric bike for me?

You can read the electric bike buying guide or use the model comparison to choose the one that is most suitable for you.

Do I need a driver's license to ride an electric bike on the road?

Click here to learn about the regulations related to electric bikes.

How long does the electric bike battery last?

Under normal usage, your battery can last for 3-4 years.

What preparations do I need to make before cycling?

Please carefully read our electric bike user manual before cycling. If necessary, you can also refer to our blog for cycling safety guidelines.

Maintenance and Troubleshooting

How do I maintain an electric bike?

Like any bicycle, electric bikes require regular maintenance to ensure safety and enjoyable riding. For more information on electric bike maintenance and cleaning, click here.

What should I do if the bike doesn't start?

Please check the cables to ensure they are not loose or disconnected. Simply loosen the black spiral wire cover until the quick disconnect plug is exposed, unplug it, and then reconnect it.

Troubleshooting guide.

1. Brake Malfunction
Check if the brake cables are loose or damaged. If not, consider replacing the brake caliper or brake lever and cable.

2. Assist Sensor Malfunction

Step1: Check if the sensor wires are loose or detached. If not, it may indicate a faulty assist sensor. Step2: Disassemble and replace the assist sensor.

3. Walk Assist Mode Error
Turn off and restart the electric bike (if the issue persists, consider replacing the controller).

4. Real-Time Mode Error
Turn off and restart the electric bike (if the issue persists, consider replacing the controller).

5. Low Voltage Error
Step 1: Remove the battery and check if it has sufficient charge. Step 2: Charge the battery. Step 3: If the issue remains after completing the first two steps, it may indicate a faulty motor. Replace the motor.

6. Motor Malfunction
Check if the motor connection wires are loose, detached, or plugged in incorrectly (if not, it may indicate a faulty motor, consider replacing the motor).

7. Twist Throttle Malfunction
Check if the connection wires are loose or detached (if not, it may indicate a faulty twist throttle, replace the twist throttle).

Brake Pad Replacement Guide

Tools Needed: Needle-nose pliers, hex wrench, replacement brake pads.

1. Removing the Brake Pads

a. Prepare the bike for maintenance. Start by turning off the bike and removing the battery.

b. Locate the brake pads. The brake pads are located inside the brake caliper on each wheel (refer to the photo).

c. Begin by removing the brake caliper. Use a hex wrench to remove the two brake caliper bolts from the bike frame (caution: be careful not to lose or misplace the washers inside the brake caliper bolts).

d. Carefully straighten the retaining pin with needle-nose pliers to remove the brake caliper bolts. Push up on the brake caliper.

e. Remove the old brake pads. Depress the spring plate to release the retaining pins and old brake pads.

2. Installing Brake Pads

a. Install the new brake pads into the brake caliper. Assemble the brake pads in the same configuration as the old ones. The friction material should be facing each other. Ensure that the top holes of each pad align with the retaining pin holes. Slide the new brake pads into the caliper to complete the installation.

b. Replace the brake pad retaining pins. Carefully bend the retaining pins to a 90° angle with needle-nose pliers to secure the brake caliper.

c. Reinstall the caliper. Position the caliper, aligning the mounting holes on the frame with the mounting points on the caliper. Insert the bolts with a hex wrench and tighten them evenly.

d. Before riding, reinstall the battery and test the brakes to ensure proper installation.

Brake Adjustment (Loose/Tight)

Tip: The best way to maintain brakes is to use both brakes simultaneously and engage the rear brake first to avoid excessive front wheel and fork tightening.

Brake adjustment includes:

· Check the wheels to ensure they are securely fastened in the frame dropouts. Improper wheel installation can cause the brake rotor to rub against the brake pads and create noise.

· Inspect the brake rotor for flatness and good condition. Damaged or dirty brake rotors can result in decreased braking performance or noise.

· Center the brake caliper by adjusting its positioning, bringing the inner pad (fixed part of the brake caliper) close to and parallel with the brake rotor. Incorrect brake pad or caliper positioning can lead to decreased braking performance or noise.

· Adjust the brake cable tension and check the brake lever. These final adjustments will help ensure properly adjusted brakes.

Crankset Replacement Guide

Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

1. Start by removing the left crank arm. Loosen the bolt with a hex wrench, then insert a crank puller tool to remove the crank arm.

2. Follow the same steps for the right-side crank arm, first remove the bolt with a hex wrench, then insert the crank puller tool into the opening.

3. Test the chain after installing the new crankset. The bike needs to be supported on a stand to elevate the rear wheel, and the crank must be rotated backward to rotate the rear wheel. Ensure the chain is properly connected to the chainrings.

PAS Sensor Replacement Guide

PAS Sensor Troubleshooting

1. Crank Removal (Refer to Crank Removal Guide)

a. Locate the PAS sensor behind the left pedal and check for any looseness.

b. If the PAS sensor is not loose, follow the cable from the PAS sensor to the connector.

c. Disconnect the PAS sensor connector and remove the controller.

d. Check for any loose connections between the controller and PAS sensor.

e.Inspect the connector for dirt, damage, or moisture. If there is dirt, damage, or moisture inside the connector, the sensor may need to be replaced.

2. PAS Sensor Replacement

a. Remove the old PAS sensor by disconnecting the cable from the main controller and loosening it.

3. PAS Sensor Installation

a. Install the new sensor, ensuring that the side with an arrow is facing towards the bike.

b. Reinstall the battery and perform a comprehensive test before riding.

Wiring Cable Troubleshooting

The wiring harness connects various electrical components on the bike. If the PUCKIPUPPY product supports indicating performing a wiring harness connector check, follow these steps to ensure the connectors are properly inserted and functioning.

Tools Needed: Hex wrench.

Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power. Flip the bike over and place it on the handlebars to prevent damage to the LCD display during maintenance.

1. Locate and remove the controller.

2. Check for loose connections in the wiring harness and reconnect them. When disconnecting the connectors, they must be pulled straight apart without twisting. If the interior looks normal, align the inner notch and pin and press them together directly without twisting.

3. Reinstall the controller following the above steps.

4. Reinstall the battery and perform a thorough test before riding.

Handlebar Grip and Stem Replacement Guide

Tools Needed: Pliers, hex wrench.

1. To remove the handlebars, start by loosening the handlebar clamp bolt.

2. Pry off the handlebar grip and slide it off the handlebars.
To remove the stem: Loosen the side bolts on the stem and then remove the center bolt from the stem. Then pull the stem off the fork.

Odometer Replacement Guide

Tools Needed: Hex wrench.

LCD Display Removal:

1. Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

2. Disconnect the LCD display connector. Follow the cable from the back of the LCD display to the wiring harness.

3. Pull apart both ends (without twisting) to disconnect the LCD display from the connecting cable.

4. Remove the LCD display. Use a hex wrench to loosen the bolts securing the LCD display, then pull it off the handlebars.

5. Remove the odometer controller. Loosen the clamping bolt with a hex wrench and remove it.

Brake Lever Replacement Guide

1. To remove the brake lever, first loosen the brake cable on the brake caliper.

2. Depress the control lever to expose the internal mechanism, then loosen the brake cable cover on the control lever.

3. Next, disconnect the cable from the brake caliper by pulling it, and loosen the bolt on the lever to remove it.

Brake Rotor Replacement Guide

1. Remove the wheel first, then remove the brake rotor (refer to the wheel replacement guide for assistance).

2. Use a hex wrench to remove the five bolts that secure the brake rotor to the wheel, then simply lift off the brake rotor.

Wheel and Fork Replacement Guide

Fork Removal:

1. Remove the bolt connecting the fork to the rear fork.

Front Wheel Removal:

(Operations similar to the initial installation of the wheel)

1. Flip the bicycle and stabilize it on the handlebars.

2. Use a wrench to loosen the two front wheel bolts on both sides. Locate and loosen the front wheel bolts, then remove them with a wrench.

3. Remove the front wheel. Lift the front wheel gently off the front fork.

Rear Wheel Removal:

1. Flip the bicycle upside down, remove the fork (as mentioned above), and then unscrew the bolt connecting the rear wheel.

2. Cut the tie wrap and disconnect the motor wires.

3. Remove the derailleur and lift the rear wheel. Separate the rear wheel by removing the brake rotor (refer to the brake rotor replacement guide).

Shifter Replacement Guide

1. To remove the shifter, cut off the end of the shifter cable and release it from the derailleur.

2. After removing the brake lever, throttle, and brake lever (refer to the brake lever, throttle, and brake lever replacement guide), unscrew the bolt from below the shifter, then slide it out and remove the shifter cable with the housing.

3. When installing a new shifter, insert the cable into the groove and push it in.

Taillight Replacement Guide

Cut the tie wrap to loosen the connection wires, then pull and remove it. Then unscrew the bolt at the back of the taillight to remove it.

Throttle Replacement Guide

1. To remove the throttle, the handlebar must be removed first (refer to the handlebar replacement guide).

2. Loosen the bolt and disconnect the wires connecting to the throttle. Pull down the throttle from the handlebar to remove it.

Derailleur Replacement Guide

1. Push the derailleur forward to release the chain from the crank.

2. Unscrew the outer chip from the derailleur and release the chain from the derailleur.

3. Unscrew the bolt of the derailleur's jockey wheel.

4. Unscrew the center bolt that connects the derailleur to the bicycle to remove it.

5. After removal, loosen the bolt that secures the derailleur cable and unscrew the derailleur cable from the derailleur.

Installation Guide:

1. When installing, first attach the derailleur to the bicycle.

2. Next, install the middle chip and thread the chain over it.

3. Install the outer chip, aligning the chain over it as shown.

4. Finally, insert the derailleur cable into the derailleur and tighten it.

Technical

Headlight Replacement GuideUnscrew the headlight bolt from the front fender and disconnect the wires to remove the headlight.

Headlight Replacement Guide

Unscrew the headlight bolt from the front fender and disconnect the wires to remove the headlight.

Derailleur Adjustment Guide

1. Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

2. Test the alignment. Rotate the pedals forward while shifting with one hand. When using the derailleur, ensure the chain smoothly moves to each gear. Test by rotating the wheel one or two full turns at a time.

a. The shifter cable tension may be too tight. Loosen the barrel adjuster on the derailleur. Rotate the barrel adjuster on the derailleur half or full turn to loosen it.

b. The derailleur cable may be too loose. Tighten the barrel adjuster on the derailleur. The derailleur barrel adjuster should rotate half to full turn.

3. Switch between all gears to test alignment. Rotate the crank forward with one hand while adjusting the gears. Ensure the derailleur smoothly moves the chain from 1st gear to 7th gear.

4. Reinstall the battery and perform a thorough test before riding.