Return Policy
Shipping Info
Warranty
Privacy Policy
Terms of Service
Cookie Policy
FAQ
Warranty

1. PUCKIPUPPY Commercial Warranty

In addition to statutory rights, PUCKIPUPPY provides a 2-year commercial warranty from delivery for eligible defects in materials and workmanship on e-bikes purchased through authorized PUCKIPUPPY channels. The commercial warranty does not reduce, replace or limit the consumer’s statutory legal guarantee.

Under the commercial warranty, confirmed eligible defects may be repaired or the affected component/product replaced. PUCKIPUPPY will cover reasonable parts and shipping costs for approved warranty service. Where mandatory law grants a broader remedy, the mandatory remedy prevails.

Commercial-warranty exclusions

The commercial warranty does not cover damage caused solely by normal wear and tear, accidents, misuse, negligent handling, improper storage, unauthorized technical modification, incompatible third-party parts, improper maintenance or assembly contrary to clear instructions. An exclusion applies only to the extent the excluded cause caused or contributed to the claimed problem.

Third-party inspection or repair does not automatically extinguish statutory rights or the entire commercial warranty. However, PUCKIPUPPY may decline commercial-warranty coverage for damage caused or worsened by an unauthorized or improper repair or modification, subject to applicable law.

2. Batteries, Wear Parts and Maintenance

Normal wear of consumable components such as tyres, inner tubes, brake pads, chains, cables and similar wear items is not itself a defect. This does not exclude statutory rights where a wear part is defective, fails prematurely because of a lack of conformity, or was not of the quality or durability reasonably expected under the contract and applicable law.

Battery damage caused by an incompatible/unauthorized charger, tampering, collision, misuse or use outside the intended product may be excluded from the commercial warranty to the extent that conduct caused the damage. Statutory rights remain unaffected.

3. Recommendation Before First Ride

Puckipuppy strongly recommends that all customers have their e-bike inspected and tested by a certified bicycle or e-bike mechanic before the first ride. A full component check helps confirm that the e-bike is safe to ride. Bicycles transported by carrier may arrive with parts that are bent, loose, or misaligned.

Customer assembly is performed at the customer’s own risk. Puckipuppy is not responsible for damage caused solely by the customer’s improper assembly, improper installation, misuse, or failure to follow clear and complete instructions. This exclusion does not apply where the issue is caused by defective parts, incomplete or incorrect instructions, packaging defects, or any other matter for which Puckipuppy is responsible under the laws of the country of purchase.

4. What This Warranty Covers

The original device and/or non-wearable parts confirmed to have eligible defects will be repaired or replaced within the applicable warranty period.

Replacement products, complimentary items, or promotional gifts are covered for 3 months unless the laws of the country of purchase require a different period.

For a replacement device, warranty coverage ends six months after the date of the replacement device or at the end of the existing warranty period, whichever is later, unless applicable law requires otherwise. Puckipuppy reserves the right to replace the device with one of equal or greater value.

Faulty batteries and motors will be repaired or replaced free of charge if Puckipuppy or an authorized service provider confirms that they qualify under the warranty terms or applicable consumer laws.

Battery warranty does not cover defects or damage caused by any of the following:

· Use of an unsuitable or unauthorized charger to charge the battery.

· A damaged seal on the battery or signs of tampering.

· Use of the battery in a device other than the intended Puckipuppy e-bike.

· Damage caused by collisions, improper use or operation, or failure to charge the battery for over one month.

5. What This Warranty Does Not Cover

· Normal wear and tear of wearable parts, including tires, tubes, brake pads, cables, housing, grips, chain, and spokes, which require regular maintenance and replacement through intended use.

· Any device that has been tampered with, modified, disassembled, or used for unintended purposes.

· Damage caused by using the e-bike in competition or in any application outside normal use.

· Damage caused by improper use, abuse, negligent handling, improper storage, accidents, failure to perform required maintenance, or improper handling.

· Consequential or incidental damage caused by failure to follow the user manual, force majeure, abuse, negligence, or improper treatment.

· Damage caused by improper tools or inadequate maintenance work not authorized by Puckipuppy.

· Damage caused by adding non-standard equipment, third-party parts, or technical modifications not approved by Puckipuppy.

· Damage caused by shipping, alteration, or repair of the product, except for shipping damage claims submitted and approved under the shipping damage process or where Puckipuppy is responsible under applicable law.

· Costs incurred when the customer uses another repair shop or service provider without Puckipuppy’s prior written approval.

· Expendable or cosmetic items such as seats, plastic parts, brake discs, brake pads, brake lines, surface scratches, paint, graphics, and other appearance-related issues that do not affect normal function.

Common wear parts include, but are not limited to:

· Hand bell.

· Shift lever.

· Rear derailleur.

· Shift cable housing.

· Freewheel.

· Chain.

· Chainring.

· Brake rotor.

· Tire assembly.

· Front fender.

· Rear fender.

· Kickstand.

· Chain protector sticker.

· Front reflector.

· Rear reflector.

6. Policy Updates and Governing Mandatory Law

We may update this policy prospectively to reflect operational or legal changes. The version applicable to an order is the version made available to the consumer in connection with that order, without prejudice to later mandatory legal rights. Nothing in this policy deprives a consumer of the protection of mandatory law that cannot lawfully be excluded by contract.

7. Important Notice

By purchasing and using a Puckipuppy e-bike, the customer acknowledges that cycling involves risks and hazards, including but not limited to traffic conditions, weather conditions, obstacles, and the behavior of other road users. The customer is responsible for safe use, maintenance, and control of the product. Puckipuppy is not liable for loss, injury, or damage resulting from improper use, improper assembly, failure to follow safety instructions, or failure to use appropriate protective gear.

8. Privacy and Data Processing Notice

When you contact us, we process your personal data (name, contact details, order information, photos or videos you provide) solely tohandle your request, on the legal basis of performance of the contract or compliance with legal obligations. Data may be transferred tooand processed by service providers outside the European Economic: Area under appropriate safeguards (e.g. EU Standard ContractualClauses). Retention periods and your rights (access, rectification, eraasure, objection, complaint to a supervisory authority) are describedd inour Privacy Policy: https://eu.puckipuppy.com/pages/privacy-policy.

Purchase

How long will it take for me to receive the electric bike I purchased?

Typical delivery time is 2–10 business days unless another estimated delivery time is displayed at checkout or in the shipping confirmation.

Delivery may take longer during public holidays, high-volume order periods, new product launches, pre-orders, restocks, logistics disruptions, or severe weather. Where possible, the estimated shipping date will be shown on the product page or communicated to you by email. 

Where do we sell and ship?

PUCKIPUPPY EU currently delivers to Germany, France, the Netherlands, Italy, Poland and Spain, subject to product availability and carrier coverage.

Delivery availability, shipping charges and estimated delivery times shown at checkout form part of your order information. 

Are taxes included?

Applicable prices, shipping charges and taxes will be displayed in accordance with applicable law and the information shown at checkout.

For the countries currently supported by PUCKIPUPPY EU, please review the final order amount displayed at checkout before completing your purchase.

Nothing in our policies limits any mandatory consumer rights available under applicable EU or national law. 

Do electric bikes need to be assembled?

Electric bikes arrive partially assembled and require a few additional steps to complete the assembly. Please carefully watch the assembly tutorial or refer to the electric bike user manual for installation instructions. Assembly Tutorial.

How can I track my order?

You can click on "Track" to view your order status.

Can discounts be stacked?

Only one coupon can be used per order, and we do not support coupon stacking. The final interpretation right belongs to PUCKIPUPPY.

Cycling

What is the most suitable electric bike for me?

You can read the electric bike buying guide or use the model comparison to choose the one that is most suitable for you.

Do I need a driver's license to ride an electric bike on the road?

Click here to learn about the regulations related to electric bikes.

How long does the electric bike battery last?

Under normal usage, your battery can last for 3-4 years.

What preparations do I need to make before cycling?

Please carefully read our electric bike user manual before cycling. If necessary, you can also refer to our blog for cycling safety guidelines.

Maintenance and Troubleshooting

How do I maintain an electric bike?

Like any bicycle, electric bikes require regular maintenance to ensure safety and enjoyable riding. For more information on electric bike maintenance and cleaning, click here.

What should I do if the bike doesn't start?

Please check the cables to ensure they are not loose or disconnected. Simply loosen the black spiral wire cover until the quick disconnect plug is exposed, unplug it, and then reconnect it.

Troubleshooting guide.

1. Brake Malfunction
Check if the brake cables are loose or damaged. If not, consider replacing the brake caliper or brake lever and cable.

2. Assist Sensor Malfunction

Step1: Check if the sensor wires are loose or detached. If not, it may indicate a faulty assist sensor. Step2: Disassemble and replace the assist sensor.

3. Walk Assist Mode Error
Turn off and restart the electric bike (if the issue persists, consider replacing the controller).

4. Real-Time Mode Error
Turn off and restart the electric bike (if the issue persists, consider replacing the controller).

5. Low Voltage Error
Step 1: Remove the battery and check if it has sufficient charge. Step 2: Charge the battery. Step 3: If the issue remains after completing the first two steps, it may indicate a faulty motor. Replace the motor.

6. Motor Malfunction
Check if the motor connection wires are loose, detached, or plugged in incorrectly (if not, it may indicate a faulty motor, consider replacing the motor).

7. Twist Throttle Malfunction
Check if the connection wires are loose or detached (if not, it may indicate a faulty twist throttle, replace the twist throttle).

Brake Pad Replacement Guide

Tools Needed: Needle-nose pliers, hex wrench, replacement brake pads.

1. Removing the Brake Pads

a. Prepare the bike for maintenance. Start by turning off the bike and removing the battery.

b. Locate the brake pads. The brake pads are located inside the brake caliper on each wheel (refer to the photo).

c. Begin by removing the brake caliper. Use a hex wrench to remove the two brake caliper bolts from the bike frame (caution: be careful not to lose or misplace the washers inside the brake caliper bolts).

d. Carefully straighten the retaining pin with needle-nose pliers to remove the brake caliper bolts. Push up on the brake caliper.

e. Remove the old brake pads. Depress the spring plate to release the retaining pins and old brake pads.

2. Installing Brake Pads

a. Install the new brake pads into the brake caliper. Assemble the brake pads in the same configuration as the old ones. The friction material should be facing each other. Ensure that the top holes of each pad align with the retaining pin holes. Slide the new brake pads into the caliper to complete the installation.

b. Replace the brake pad retaining pins. Carefully bend the retaining pins to a 90° angle with needle-nose pliers to secure the brake caliper.

c. Reinstall the caliper. Position the caliper, aligning the mounting holes on the frame with the mounting points on the caliper. Insert the bolts with a hex wrench and tighten them evenly.

d. Before riding, reinstall the battery and test the brakes to ensure proper installation.

Brake Adjustment (Loose/Tight)

Tip: The best way to maintain brakes is to use both brakes simultaneously and engage the rear brake first to avoid excessive front wheel and fork tightening.

Brake adjustment includes:

· Check the wheels to ensure they are securely fastened in the frame dropouts. Improper wheel installation can cause the brake rotor to rub against the brake pads and create noise.

· Inspect the brake rotor for flatness and good condition. Damaged or dirty brake rotors can result in decreased braking performance or noise.

· Center the brake caliper by adjusting its positioning, bringing the inner pad (fixed part of the brake caliper) close to and parallel with the brake rotor. Incorrect brake pad or caliper positioning can lead to decreased braking performance or noise.

· Adjust the brake cable tension and check the brake lever. These final adjustments will help ensure properly adjusted brakes.

Crankset Replacement Guide

Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

1. Start by removing the left crank arm. Loosen the bolt with a hex wrench, then insert a crank puller tool to remove the crank arm.

2. Follow the same steps for the right-side crank arm, first remove the bolt with a hex wrench, then insert the crank puller tool into the opening.

3. Test the chain after installing the new crankset. The bike needs to be supported on a stand to elevate the rear wheel, and the crank must be rotated backward to rotate the rear wheel. Ensure the chain is properly connected to the chainrings.

PAS Sensor Replacement Guide

PAS Sensor Troubleshooting

1. Crank Removal (Refer to Crank Removal Guide)

a. Locate the PAS sensor behind the left pedal and check for any looseness.

b. If the PAS sensor is not loose, follow the cable from the PAS sensor to the connector.

c. Disconnect the PAS sensor connector and remove the controller.

d. Check for any loose connections between the controller and PAS sensor.

e.Inspect the connector for dirt, damage, or moisture. If there is dirt, damage, or moisture inside the connector, the sensor may need to be replaced.

2. PAS Sensor Replacement

a. Remove the old PAS sensor by disconnecting the cable from the main controller and loosening it.

3. PAS Sensor Installation

a. Install the new sensor, ensuring that the side with an arrow is facing towards the bike.

b. Reinstall the battery and perform a comprehensive test before riding.

Wiring Cable Troubleshooting

The wiring harness connects various electrical components on the bike. If the PUCKIPUPPY product supports indicating performing a wiring harness connector check, follow these steps to ensure the connectors are properly inserted and functioning.

Tools Needed: Hex wrench.

Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power. Flip the bike over and place it on the handlebars to prevent damage to the LCD display during maintenance.

1. Locate and remove the controller.

2. Check for loose connections in the wiring harness and reconnect them. When disconnecting the connectors, they must be pulled straight apart without twisting. If the interior looks normal, align the inner notch and pin and press them together directly without twisting.

3. Reinstall the controller following the above steps.

4. Reinstall the battery and perform a thorough test before riding.

Handlebar Grip and Stem Replacement Guide

Tools Needed: Pliers, hex wrench.

1. To remove the handlebars, start by loosening the handlebar clamp bolt.

2. Pry off the handlebar grip and slide it off the handlebars.
To remove the stem: Loosen the side bolts on the stem and then remove the center bolt from the stem. Then pull the stem off the fork.

Odometer Replacement Guide

Tools Needed: Hex wrench.

LCD Display Removal:

1. Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

2. Disconnect the LCD display connector. Follow the cable from the back of the LCD display to the wiring harness.

3. Pull apart both ends (without twisting) to disconnect the LCD display from the connecting cable.

4. Remove the LCD display. Use a hex wrench to loosen the bolts securing the LCD display, then pull it off the handlebars.

5. Remove the odometer controller. Loosen the clamping bolt with a hex wrench and remove it.

Brake Lever Replacement Guide

1. To remove the brake lever, first loosen the brake cable on the brake caliper.

2. Depress the control lever to expose the internal mechanism, then loosen the brake cable cover on the control lever.

3. Next, disconnect the cable from the brake caliper by pulling it, and loosen the bolt on the lever to remove it.

Brake Rotor Replacement Guide

1. Remove the wheel first, then remove the brake rotor (refer to the wheel replacement guide for assistance).

2. Use a hex wrench to remove the five bolts that secure the brake rotor to the wheel, then simply lift off the brake rotor.

Wheel and Fork Replacement Guide

Fork Removal:

1. Remove the bolt connecting the fork to the rear fork.

Front Wheel Removal:

(Operations similar to the initial installation of the wheel)

1. Flip the bicycle and stabilize it on the handlebars.

2. Use a wrench to loosen the two front wheel bolts on both sides. Locate and loosen the front wheel bolts, then remove them with a wrench.

3. Remove the front wheel. Lift the front wheel gently off the front fork.

Rear Wheel Removal:

1. Flip the bicycle upside down, remove the fork (as mentioned above), and then unscrew the bolt connecting the rear wheel.

2. Cut the tie wrap and disconnect the motor wires.

3. Remove the derailleur and lift the rear wheel. Separate the rear wheel by removing the brake rotor (refer to the brake rotor replacement guide).

Shifter Replacement Guide

1. To remove the shifter, cut off the end of the shifter cable and release it from the derailleur.

2. After removing the brake lever, throttle, and brake lever (refer to the brake lever, throttle, and brake lever replacement guide), unscrew the bolt from below the shifter, then slide it out and remove the shifter cable with the housing.

3. When installing a new shifter, insert the cable into the groove and push it in.

Taillight Replacement Guide

Cut the tie wrap to loosen the connection wires, then pull and remove it. Then unscrew the bolt at the back of the taillight to remove it.

Throttle Replacement Guide

1. To remove the throttle, the handlebar must be removed first (refer to the handlebar replacement guide).

2. Loosen the bolt and disconnect the wires connecting to the throttle. Pull down the throttle from the handlebar to remove it.

Derailleur Replacement Guide

1. Push the derailleur forward to release the chain from the crank.

2. Unscrew the outer chip from the derailleur and release the chain from the derailleur.

3. Unscrew the bolt of the derailleur's jockey wheel.

4. Unscrew the center bolt that connects the derailleur to the bicycle to remove it.

5. After removal, loosen the bolt that secures the derailleur cable and unscrew the derailleur cable from the derailleur.

Installation Guide:

1. When installing, first attach the derailleur to the bicycle.

2. Next, install the middle chip and thread the chain over it.

3. Install the outer chip, aligning the chain over it as shown.

4. Finally, insert the derailleur cable into the derailleur and tighten it.

Technical

Headlight Replacement GuideUnscrew the headlight bolt from the front fender and disconnect the wires to remove the headlight.

Headlight Replacement Guide

Unscrew the headlight bolt from the front fender and disconnect the wires to remove the headlight.

Derailleur Adjustment Guide

1. Prepare the bike for maintenance. Remove the battery and hold the power button for 10 seconds to discharge any remaining power.

2. Test the alignment. Rotate the pedals forward while shifting with one hand. When using the derailleur, ensure the chain smoothly moves to each gear. Test by rotating the wheel one or two full turns at a time.

a. The shifter cable tension may be too tight. Loosen the barrel adjuster on the derailleur. Rotate the barrel adjuster on the derailleur half or full turn to loosen it.

b. The derailleur cable may be too loose. Tighten the barrel adjuster on the derailleur. The derailleur barrel adjuster should rotate half to full turn.

3. Switch between all gears to test alignment. Rotate the crank forward with one hand while adjusting the gears. Ensure the derailleur smoothly moves the chain from 1st gear to 7th gear.

4. Reinstall the battery and perform a thorough test before riding.